The event of spontaneous combustion is the reason for several cases of fires in the coal mining industry. It is well-known that carbonaceous materials such as coal and coal-shales undergo self-heating when exposed to atmospheric conditions. Self-heating occurs naturally due to the chemical reactions between oxygen and coal and other carbonaceous materials. The spontaneous combustion characteristics of coal may be influenced by the natural convection within a coal seam, waste dumps and other mining piles (Moghtaderi et al. 2000).

Self-heating of coal-shales has been reported in the South African coal mines to be capable of starting spontaneous combustion but not the coals alone (Onifade and Genc 2018b, c, d). This incident has been observed in areas such as overburden shales, selected bands of a coal seam, spoil heaps and highwall (Figs. 1 , 2). It is known that coal, roof shales and spoil heaps may become self-heated and liberate heat naturally under favourable weather conditions. Sedimentary rocks such as coal and coal-shale, consist of certain amounts of organic matter (macerals) and inorganic materials (mainly crystalline) causing them to likely undergo self-heating leading to spontaneous combustion (Onifade and Genc 2018d). Reactive sedimentary materials have pore spaces embedded in the solid together with the occurrence of a carbon-rich element (Dullien 1979). This renders the rock porous to different fluids like water and air, increases its surface area, thus making the organic particles reactive as it permits oxidation to occur (Dullien 1979). Such reactive materials might experience spontaneous combustion. Spontaneous combustion of coals and coal-shales is an important phenomenon that requires in-depth investigation. Studies of self-heating of coal-shales in selected bands of coal seams and highwalls are limited (Onifade et al. 2018; Onifade and Genc 2018d). Limited information is available to investigate and predict the spontaneous combustion liability of coal-shales in relation to coals. However, these are materials that comprise a number of varying microscopic and inorganic constituents for spontaneous combustion in old workings, spoil heaps and abandoned mines.

a Self-heating of run-of-mine and b spoil heaps at Tweefontein Mine, Witbank, South Africa

a Signs of self-heating in coal seam at Khwezela Mine (Bokgoni Pit) and b self-heating of in-seam shale at Goedgevonden Colliery, Witbank, South Africa

Many investigations have been carried out on the self-heating characteristics of coal, both experimentally and computationally (Gouws and Wade 1989a, b; Genc and Cook 2015; Stracher and Taylor 2004; Kucuk et al. 2003; Carras and Young 1994; Onifade et al. 2018; Onifade and Genc 2018b, c,d), but only limited studies exist on other reactive materials. The occurrence of various intrinsic and extrinsic parameters influencing the start and development of spontaneous combustion is the reason for the difficulties in understanding the mechanism of spontaneous combustion. Most of these parameters have been reported by many researchers (Kaymakci and Didari 2002; Banerjee 1985; Kim 1977; Beamish and Blazak 2005; Falcon 2004; Panigrahi and Sahu 2004; Panigrahi and Saxena 2001; Ren et al. 1999) to predict the self-heating characteristics of coal.

This study evaluated the intrinsic properties of some South African bituminous coals and coal-shales using characterisation tests (proximate, ultimate and petrographic analyses), following standard experimental procedures. Furthermore, a statistical interpretation of coals and coal-shales analysis data and the combined effects of the major intrinsic factors affecting their liability towards spontaneous combustion for predictive purposes were examined. An understanding of these factors may be important in understanding the spontaneous combustion liability of coals and coal-shales in coal mines.

2.1 Sample collection and preparation

Fourteen coals and fourteen coal-shales used for this study were collected (using the ply sampling technique) from four coal mines (iMpunzi Mine, Goedgevonden Colliery, Khwezela Mine, and Tweefontenin Mine) in Witbank, South Africa. The samples were sealed in airtight bags (plastic), immediately after collection to avoid moisture loss and oxidation. The airtight bag is produced using aluminium-coated polyester which allows maximum reduction of vapour and oxygen permeability. Each ply sample bag was clearly labelled with a chosen number. Samples of bituminous coal and coal-shales were collected from a selected band of the coal seams (Witbank coalfields) and highwalls as shown in Figs. 1 and 2. The samples were selected in respect of their high propensity to oxidation from the areas known to be prone to spontaneous combustion. The samples were stored and prepared under laboratory conditions (room temperature). The sample lumps were reduced using a crusher (Rocklabs MK III) to suitable sizes (> 10 mm). The samples were milled to 250 µm size fraction for proximate, ultimate, total sulphur and forms of sulphur, 212 µm for spontaneous combustion tests, while for petrographic analysis the samples were milled to ≤ 1000 µm according to the South African National Standard (SANS, 7404 Parts 1–5), blended and divided using a centrifugal mill (Retsch ZM 200) to generate different sub-samples. Proximate, elemental and petrographic analysis, and spontaneous combustion tests (Wits-Ehac Index and Wits-CT Index) were carried out.

2.2 Characterisation tests

The experimental tests involving the determination of the moisture, ash, volatile matter and fixed carbon contents were carried out according to the American Society for Testing and Material (ASTM) standards (ASTM, D-3173-17a, ASTM, D-3174-11, ASTM, D-3175-17). Fixed carbon was obtained by subtracting the sum of the percentage of ash, moisture and volatile matter from 100 (ASTM, D3176-15). The carbon, hydrogen, nitrogen and total sulphur content were determined using a LECO TruSpec CHN and C and S analyzer according to the International Standard Organisation Standards (ISO 12902: 2001). Oxygen content was calculated by subtracting the sum of the percentage of moisture, ash, carbon, hydrogen, nitrogen and sulphur from 100. The results are reported in weight percent of air-dried (wt%, ad). Pyritic sulphur was detected in selective digestion with hydrogen nitrate (HNO₃) and analysed by inductively coupled plasma optical emission (ICP-OES), while sulphate sulphur was detected in selective digestion with hydrogen chloride (HCl) and analysed by photometric method as barium sulphate (BaSO4). Organic sulphur is taken as the difference between the total sulphur and the sum of the sulphate and pyritic sulphur. Maceral analysis including mineral matter was conducted to evaluate the organic and inorganic content of the samples. A Zeiss Axio Imager M2 M reflected light petrographic microscope fitted with oil immersion lens at a total magnification of 500× was used. The petrographic pellets and/or blocks used for the petrographic analyses were produced by mixing 2–3 g of the grain size specified (≤ 1000 µm) according to the South African National Standard (SANS, 7404 Parts 1–5) with epoxy resin in a 3.2 cm diameter phenolic ring form moulds. The moulds were allowed to cure, and ground with the use of 320, 400 and 1000 grit papers. Once ground, they were polished using 1.0 and 0.3 μm alumina slurries on various cloth. Final polishes were achieved with the use of colloidal silica, which provides relief free and scratch-free surfaces for analysis by reflectance microscopy. The macerals results including petrographically observable mineral matter are reported as volume percent (vol%), inclusive of mineral matter or mineral matter free basis (vol%, mmf).

2.3 Wits-Ehac tests

The Wits-Ehac Index was developed in South Africa in the late 1980s to test the spontaneous combustion liability of coal (Eroglu 1992; Genc et al. 2018; Genc and Cook 2015; Gouws and Wade 1989a, b; Onifade et al. 2018; Onifade and Genc 2018a, b, d; Wade 1989). The testing apparatus consists of an oil bath, six coal and inert material cell assemblies, an oil circular, a heater, a flowmeter, an air supply compressor and a computer (Wade et al. 1987) as shown in Fig. 3a. Freshly pulverized (< 212 µm) dried coal samples (under room temperature) of 20–25 g in weight is used. The test apparatus is used to test coals under predefined conditions and a spontaneous combustion liability index is obtained. The testing apparatus incorporates the determined crossing point temperatures (XPT) and differential thermal analysis (DTA) from selected coal samples with periodic measurement of temperatures to obtain a consistent self-heating liability index termed the Wits-Ehac Index. The coal temperatures are recorded every 30 s by the computer over an average of 4 h for the oil in the bath to be heated to 200 °C. When the temperature difference between the inert material (calcined aluminium) and the coal sample is plotted against the inert temperature, the part of the graph where the coal is heating faster than the inert sample (where an exothermic reaction occurs) is termed Stage II. The index makes use of the fact that coal highly prone to self-heat have a steeper stage II slope and lower XPT than coal not highly prone to self-heat. When using DTA, the difference in temperatures between the coal sample and an inert material sample is measured via a data logger, stored in a computer and plotted against the temperature of the inert material sample. It is important to understand that during DTA, three stages are obtainable. At first, the temperature of an inert material sample is higher than the temperature of the coal sample (Stage l), which is dependent on the cooling effect of the evaporation of the coal sample moisture content. Secondly, evaporation of the moisture content; the coal sample begins to heat up at a higher rate than the heating rate of the inert material (Stage II) and this is based on the liability of coal to self–heating and attempting to reach the temperature of the surrounding temperature (oil bath temperature). Lastly, the high exothermicity is reached at a point where the line crosses the zero base line and is referred to as the XPT. Uludag et al. (2001) indicated the three stages in a study and described that stage I starts with minimal differential and progressively increases towards the XPT where the differential is zero. Stage II continues from the XPT to the point referred to as kick–point. In addition, Stage II is one of the best indicators of spontaneous combustion. Stage III is when the coal starts to burn beyond the kick–point. According to Wade et al. (1987), coals with a spontaneous combustion liability index below 3 are considered to be low risk, 3–5 medium risk, and coals with values > 5 are considered to be highly liable to spontaneous combustion. The index is calculated from the formula in Eq. 1. Using this formula, MS Excel calculates the stages and generates the thermogram (Fig. 3b).

a Wits-Ehac test apparatus set-up (Wade et al. 1987); b A typical differential analysis thermogram

2.4 Wits-CT tests

The Wits-Ehac Index was developed in South Africa to test the spontaneous combustion liability of coal. However, in some cases, the Wits-Ehac Index fails to produce tangible results when testing coal-shales. To overcome this problem, a new apparatus has been developed to test coals and coal-shales under chemical reactions with oxygen and an index has been obtained (Onifade et al. 2018). A device for predicting the spontaneous combustion liability of coal, coal-shale and other carbonaceous materials under the influence of oxygen without any heating system was recently developed in the School of Mining Engineering, University of the Witwatersrand, and is referred to as the Wits-CT test. The liability of various samples to spontaneous combustion were evaluated for 24 h under the influence of oxygen. This experiment was designed to evaluate the temperature differences within the shortest period of time in a coal mass under the influence of oxygen.

The equipment has a capacity to accept a 15 kg sample, depending on the packing density. In order to determine spontaneous combustion liability via self-heating, a representative sample of particle size (< 6.39 mm) is weighed and loaded into an autoclave. The process is repeated until the autoclave is filled to the marked point and the lid is fixed and fastened as soon as the autoclave is full. This technique of preparation gives a closely sized sample that is preferable to measure the rate of oxidation. Three thermocouples each with two temperature probes are inserted into the column as the correct sample level is reached. Three uniformly separated temperature sensors placed along the length of the autoclave are used to check and record the temperature measurements. The sensor arrangement is typically located at different points within the autoclave (locations A, B, and C within the interior of the container). Each of the three thermocouples has two temperature sensors which measure temperatures at different levels at the locations A, B, and C in order to keep a recording of the temperature distribution during the reaction of a carbonaceous material and oxygen. At location A, sensors are located at levels 13 and 23 cm within the container, location B, 53 and 63 cm, and location C, 33 and 43 cm.

Oxygen is supplied and controlled at a fixed flow rate (20 mL/min) by means of a flowmeter before being fed into a manifold attached below the lid of the autoclave Table 1. The changes in temperature distributions are recorded by the data logger every minute over 24 h. The Wits-CT Index uses the total carbon content and the temperature differences due to the reaction with oxygen to predict the spontaneous combustion liability. According to Onifade et al. (2018), coals and coal-shales with a spontaneous combustion liability index below 2.5 are considered to be less reactive, 2.5–5 moderately reactive, 5–7.5 reactive, and > 7.5 are considered to be highly liable to spontaneous combustion. An illustration of the experimental setup is indicated in Fig. 4. The index is calculated from the formula in Eq. 2.

where, T_M is the difference between the sum of maximum temperatures of each thermocouple inside the equipment and the room temperature (22 °C), T_R is the difference between the maximum temperature and the initial temperature during oxidation reaction in degree Celsius,  %C_ad is the air-dried percentage of carbon content of the sample, × is the multiplication sign and 24 is the duration of the test (24 h) and it is constant.

Wits-CT apparatus (Onifade et al. 2018)

3.1 Statistical analysis

The results for characterisation tests (proximate, elemental and petrographic analysis) and spontaneous combustion tests (the Wits-Ehac Index and the Wits-CT Index) carried out on the samples are presented in Tables 2, 3, 4, 5 and 6 respectively. The evaluation of coal and coal-shales intrinsic factors affecting spontaneous combustion was at first based on data obtained from the spontaneous combustion liability tests and the intrinsic properties as determined in the laboratory. It is appropriate to group the data into dependent (the Wits-Ehac Index and the Wits-CT Index) and independent (intrinsic properties) variables in order to make the analyses meaningful. The observed temperatures values of spontaneous combustion tests are dependent on the coal and coal-shale properties, coal-forming elements and coal structure. Hence, the statistical analysis was carried out by correlating the samples intrinsic properties and spontaneous combustion liability indices. The range value (Table 1) is the value of the independent variables from the lowest to the highest. The R-squared value is a statistical tool which can either carry out hypothesis testing or predict future result on the basis of related information. It provides a measure of how well observed outcomes are reproduced by a model on the basis of the proportion of total variation of outcomes described by the model (Draper and Smith 1998; Glant 1990). The higher the R-squared value, the better the fit is. In statistics, the correlation coefficient measures the strength and direction of a linear relationship between two variables (dependent and independent variables) on a scatter plot (Deborah 2016; Stigler 1989). The range of values for the correlation coefficient is −1.0 to 1.0 and it is a representation of the linear interdependence of two variables or sets of data. The correlation coefficients were obtained using the data analysis in MS Excel. A correlation coefficient of −1.0 indicates a perfect negative correlation, while a correlation of 1.0 indicates a perfect positive correlation. A correlation coefficient of 1.0 indicates a perfect positive relationship between two variables. i.e. for a positive increase in one variable, there is also a positive increase in the second. A correlation coefficient of −1.0 indicates a perfect negative relationship between the two variables. i.e. the variables move in opposite directions, for a positive increase in one variable, there is a decrease in the second variable. A zero correlation means that for every increase, there is no positive or negative increase (i.e. the two are not related). The R-squared values and the correlation coefficients were used to measure the trends and any significant relationships between the intrinsic properties and the Wits-Ehac Index and Wits-CT Index. The overall database involved the spontaneous combustion test results and intrinsic properties of 14 coals and 14 coal-shales in order to determine the factors affecting spontaneous combustion. The study interpreted the linear relationship between the intrinsic properties and spontaneous combustion liability index based on the set criterion (Table 1).

The criterion is established based on the strength and directions of a linear relationship between the intrinsic properties and spontaneous combustion liability index on a scatter plot. Statistically correlations of +1 or −1 are expected, however, this is not possible due to the use of real dataset from experimental tests, and real data are never perfect to get a perfect correlation coefficient (Deborah 2016). Since the results of the real data is expected to determine how close is close enough to indicate a strong, moderate or weak linear relationship, this necessitated the need to interpret the correlation coefficient values, classify and find how close they are using the set criterion (Table 1). Given that the correlation coefficient measures the degree to which how two variables vary together, establishing a criterion means whether each intrinsic property and spontaneous combustion liability index vary strongly, moderately or weakly and if it is a positive or negative relationship. The higher the correlation coefficient, the stronger the relationship is (higher correlation coefficients means a better prediction).

3.2 Linear regression analysis

The results of the characterisation tests were correlated with the spontaneous combustion liability indices (Wits-Ehac Index and the Wits-CT) statistically. Data from the experimental tests using the linear regression analysis is given in the Tables 2, 3, 4, 5 and 6 and the values in brackets are in negative sign.

As a preliminary step, the experimental data was analysed using statistical methods to ascertain whether any of the parameters were linearly related to the oxidation potential. The dataset was divided into dependent and independent variables in order to establish trends and relationships. The correlation coefficients between the independent and dependent variables are seen in Tables 2, 3, 4, 5 and 6. The linear regression analysis was used to identify if there are better linear relationships between dependent and independent variables. It was found that each factor has an influence towards spontaneous combustion based on their relationships.

The statistical analysis demonstrated the better linear relationship between the dependent and independent variables in most cases based on the R-squared values (Figs. 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16) and correlation coefficients obtained. The higher correlation coefficients obtained from the data sets suggest that this may be the best way to minimize the overriding effect of the various coals and coal-shales on analysis of the general oxidation trends. Thus, obtaining a result which may be an indication of spontaneous combustion liability of certain carbonaceous materials. It is well-known that carbonaceous materials behaves differently when subjected to similar atmospheric conditions due to differences in their physical and chemical properties. The analysis of variable pairs (moisture/Wits-Ehac Index; moisture/Wits-CT Index; volatile matter/Wits-Ehac Index; volatile matter/Wits-CT Index; ash/Wits-Ehac Index; ash/Wits-CT Index and etc.) demonstrated uniform trends, i.e. the oxidation trend increases with increasing volatile matter, carbon, hydrogen, etc. and decreases with increasing ash and mineral matter, etc. for both coal and coal-shale samples. Working with carbonaceous materials having similar rank make it difficult to establish significant relationships between the petrographic composition and spontaneous combustion liability as was expected before regression. This is in-line with the study reported by Eroglu (1992). Few significant relationships were found between the spontaneous combustion liability indices and petrographic composition (total vitrinite, total inertinite and total liptinite) from the statistical analysis. However, it was decided to investigate the relationship between the various constituents of each maceral group on spontaneous combustion liability results.

Influence of proximate and ultimate analysis on spontaneous combustion of coals

Influence of proximate and ultimate analysis on sponatneous combustion of coal-shales

Influence of vitrinite and its group on spontaneous combustion of coals

Influence of vitrinite and its group on spontaneous combustion of coal-shales

Influence of inertinite and its group on spontaneous combustion of coals

Influence of inertinite and its group on spontaneous combustion of coals

Influence of inertinite and its group on spontaneous combustion of coal-shales

Influence of inertinite and its group on spontaneous combustion of coal-shales

Influence of liptinite, other macerals, petrographically observable mineral matter on spontaneous combustion of coals

Influence of liptinite, other macerals, petrographically observable mineral matter on spontaneous combustion of coals

Influence of liptinite, other macerals and petrographically observable mineral matter on spontaneous combustion of coal-shales

Influence of liptinite, other macerals, petrographically observable mineral matter and its group on spontaneous combustion of coal-shales

From Tables 2, 3, 4, 5, 6 and 7, based on the criterion set, it was found that contents of volatile matter, 0.5164; ash, −0.6884; carbon, 0.6572; hydrogen, 0.6616; nitrogen, 0.6945; sulphate sulphur, 0.6422; and inertinite macerals [fusinite, 0.5663] with strong effect size are parameters affecting spontaneous combustion liability of coals. Furthermore, it was found that contents of moisture, 0.7715; volatile matter, 0.6389; ash, −0.8352; carbon, 0.7962; hydrogen, 0.5795; nitrogen, 0.6446; total sulphur, 0.5791; and its forms [pyritic, 0.5704; sulphate, 0.5365; and organic sulphur, 0.5933], total inertinite, 0.7360; and its constituents [fusinite, 0.5898; total semifusinite, 0.7776; secretinite, 0.6003; and total inertodetrinite, 0.7749] total maceral, 0.7653; and mineral matter, −0.7653 with strong effect size are factors affecting spontaneous combustion liability of coal-shales. The linear regression analysis shows that both liability indices show better linear relationships with some of the intrinsic properties and thus, identifies the major intrinsic factors affecting spontaneous combustion liability. Previous studies by Falcon (2004); Gouws and Wade (1989a); Sahu et al. 2005; Kaymacki and Didari (2002); and Nimaje and Tripathy (2016) indicated that intrinsic properties are a measure of spontaneous combustion liability. The effects of coals and coal-shales intrinsic properties on spontaneous combustion liability are shown in Figs. 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 and 16 using linear regression analysis.

3.3 Effects of intrinsic properties on spontaneous combustion of coal and coal-shale samples

Figures 5l and 6a show the effect of moisture content on the spontaneous combustion liability of the coals obtained from the linear regression analysis. The results indicated a negative correlation for the coals and a positive correlation for the coal-shales. As the correlation displays R-squared of 0.3418 for coals, it shows that the linear model has a moderate strength. It is different for the coal-shales. Here the R-squared is higher, 0.5952, than the coals. This means the coal-shales have a strong effect size.

The R-squared value for volatile matter is considered as 0.2666 for coals and 0.4763 for coal-shales (Figs. 5b and 6m). This is an indication that both coals and coal-shales have a moderate effect size. There is a positive relationship between volatile matter and spontaneous combustion liability index for both cases. This means that as the volatile matter increases, the oxidation capacity of coals and coals-shales is more likely to increase in general. This is in-line with the study reported on coal by Singh and Demirbilek (1987).

There is a negative relationship between the ash content and spontaneous combustion liability index for both coals and coal-shales. This means that as ash content increases, the spontaneous combustion liability decreases. This is in-line with the study reported on coal by Beamish and Blazak (2005), Singh and Demirbilek (1987). The relationship between the ash content and spontaneous combustion liability index seems to be strong. The R-squared value is 0.75 for coals and 0.8926 for coal-shales (Figs. 5n and 6n). The value for coals and coal-shales have a strong effect size. The decreasing ash content affects the oxidation potential by causing a relatively high spontaneous combustion liability for both coals and coal-shales analysed. This is in-line with the studies reported on coal by Beamish and Arisoy (2008), Humphreys et al. (1981), Panigrahi and Sahu (2004); Smith et al. (1988).

The R-squared value for the carbon content is 0.7336 for coals and 0.9273 for coal-shales (Figs. 5o and 6o). The relationship between carbon content and spontaneous combustion liability index for coals and coal-shales seems to be strong. The value for coals and coal-shales have a strong effect size. There is a positive relationship between the carbon content and spontaneous combustion liability index for both the coals and coal-shales. This means that as the carbon content increases, the oxidation capacity of coals and coal-shales are more likely to increase in general. The increasing carbon content affects the oxidation potential of both coals and coal-shales by causing a relatively high spontaneous combustion liability.

There is a positive relationship between the hydrogen content and spontaneous combustion liability index for both the coals and coal-shales. This means that as the hydrogen content increases, the oxidation capacity of coals and coal-shales is more likely to increase in general. The increasing hydrogen content affects the oxidation potential of both coals and coal-shales by causing a relatively high spontaneous combustion liability. The R-squared value for the hydrogen content is 0.5703 for coals and 0.7742 for coal-shales (Figs. 5p and 6p). The relationship between the hydrogen content and spontaneous combustion liability index for coals and coal-shales are a strong positive.

The R-squared value for the nitrogen content is 0.7026 for coals and 0.8953 for coal-shales (Figs. 5q and 6q). The relationship between the nitrogen content and spontaneous combustion liability index for coals and coal-shales are a strong positive. This means that as the nitrogen content increases, the oxidation potential of coals and coal-shales is more likely to increase in general.

Figures 5r and 6r show the effect of calculated oxygen on the spontaneous combustion liability of the coals and coal-shales obtained from the linear regression analysis. The evaluation of the calculated oxygen indicated a negative correlation for the coals and a positive correlation for the coal-shales. As the correlation (Fig. 5r) displays R-squared of 0.0103 for coals, it shows that the linear model does not fit well. It is different for the coal-shales. Here, the R-squared is a bit higher, 0.1052, than the coals. The coals and coal-shales have a very weak effect size.

The evaluation of the total sulphur indicated a negative correlation for the coals and a positive correlation for the coal-shales (Figs. 5h and 6h). This is in-line with the study reported on coal by Singh and Demirbilek, (1987). As the correlation displays an R-squared value of 0.0047 for coals (Fig. 5h), it shows that the linear model does not fit well. It is different for the coal-shales. Here, the R-squared value is a bit higher, 0.3353, than the coals. The value of coals has a very weak effect size, while the value for coal-shales have a moderate effect size.

The R-squared value for pyritic sulphur is 0.0076 for coals and 0.3254 for coal-shales (Figs. 5i and 6i). This is in-line with the study reported on coal by Singh and Demirbilek (1987). The evaluation of the pyritic sulphur indicated a positive correlation coefficient for both the coals and coal-shales. This means that as the pyritic sulphur increases, the oxidation potential of coals and coal-shales is more likely to increase in general. The scatter plots show that the corresponding spontaneous combustion liability values display a wide variation. The value for coals have a very weak effect size, while coal-shales have a moderate effect size. The linear regression analysis was quite similar to those obtained from the total sulphur content data.

The R-squared value for sulphate sulphur is 0.5806 for coals and 0.2878 for coal-shales (Figs. 5u and 6j). The value for coals have a strong effect size, while the value for coal-shales have a moderate effect size. The evaluation of the sulphate sulphur indicated a negative correlation for the coals and a positive correlation for the coal-shales. This means that as sulphate sulphur increases for the coals, the spontaneous combustion liability decreases, while for the coal-shales as the pyritic sulphur increases, the oxidation potential is more likely to increase in general. This is in-line with the study reported on coal by Singh and Demirbilek (1987). The scatter plots show that the corresponding spontaneous combustion liability values display a wide variation which is quite similar to that obtained from the total sulphur and pyritic sulphur data.

The evaluation of the organic sulphur indicated a negative correlation for the coals and a positive correlation for the coal-shales. This means that as organic sulphur increases for the coals, the spontaneous combustion liability decreases, while for the coal-shales as the organic sulphur increases, the oxidation potential is more likely to increase in general. This is in-line with the study reported on coal by Singh and Demirbilek (1987). The R-squared value for organic sulphur is considered as 0.0849 for coals and 0.3519 for coal-shales (Figs. 5v and 6k). The value for coals have a very weak effect size, while the value for coal-shales have a moderate effect size.

The graphs of the major macerals (vitrinite, inertinite and liptinite) and spontaneous combustion liability index indicates that there may be relationships even though the R-squared values and correlation coefficients are very weak in most cases. A similar study is reported by Eroglu (1992). The analysis showed that the relationships between the various maceral groups and the oxidation potential may be significant when the maceral constituents were unpacked either in the mineral matter free basis (mmf) or inclusive of mineral matter. The results of the linear regression analysis obtained indicated that the various maceral groups have either a positive or negative effect size (Figs. 7, 8, 9, 10, 11, 12, 13, 14, 15 16). It was found that the majority of the vitrinite and its group (collotelinite and collodetrinite) and liptinite and its group (sporinite) in both cases have a very weak effect size. Inertinite macerals (total inertodetrinite, total semifusinite, fusinite and secretinite) shows a better linear relationship to oxidation potential more than the vitrinite and liptinite macerals. The study indicated that the oxidation potential of coals and coal-shales may be influenced by the amount of each maceral composition. This is in-line with the studies reported on coal by (Falcon 1987; Scott and Glasspool 2007). Petrographically observable mineral matter in the coal-shales show a better linear relationship to oxidation potential than the coals (Figs. 14e and 16e).

The study showed that there is a tendency of an increase in intrinsic properties such as moisture, volatile matter, ash, carbon, total sulphur, calculated oxygen, pyritic sulphur, organic sulphur, inertinite macerals and petrographically observable mineral matter in both coals and coal-shales but this seems to be more pronounced for coal-shales than for the coals, while coals seem to be more pronounced in terms of hydrogen, nitrogen and sulphate sulphur content than coal-shales. The inconsistencies (i.e. an independent variable with positive correlation coefficient with the Wits-Ehac Index may have a negative correlation with the Wits-CT Index) in the correlation coefficients between the dependent (Wits-Ehac Index and Wits-CT Index) and independent (some of the intrinsic properties) variables cannot allow accurate determination of the major intrinsic properties affecting spontaneous combustion liability. Similar studies reported different correlation coefficients between some intrinsic factors (moisture, volatile matter, carbon, nitrogen, inertinite, vitrinite, exinite, total sulphur, pyritic sulphur, organic sulphur and calorific value) and the spontaneous combustion liability indices (Kaymakci and Didari 2002; Singh and Demirbilek 1987). The inconsistencies in the trend of correlation coefficients necessitated the developed models (Table 8). It is known that different methods have been used by previous studies to measure the spontaneous combustion liability of coals but no standard method has been considered the best in predicting spontaneous combustion liability (Stott 1980; Wade et al. 1987; Cliff et al. 1998; Beamish et al. 2001). This study investigated the factors affecting spontaneous combustion liability of coals and coal-shales using two different spontaneous combustion test methods (the Wits-Ehac Index and the Wits-CT Index) and evaluates the factor affecting these materials using statistical analysis. The two liability indices have been used to predict the spontaneous combustion liability of these materials and the results are in-line (Onifade and Genc 2018a, b). Limited studies have been conducted to establish relationships between two or more different spontaneous combustion liability indices and selected intrinsic properties (Singh and Demirbilek 1987). This study established that some intrinsic properties show different linear trends (i.e. positive or negative correlation coefficients) with spontaneous combustion liability indices due to either the method of calculating the value of each index or the range of values assigned to represent each index for risk classification (see Wits-Ehac test and Wits-CT test procedures).

3.4 Multiple regression analysis

The study indicated that the use of single variable equations obtained from the linear regression analysis to predict the spontaneous combustion liability of coals and coal-shales is an unreliable method (Tables 2, 3, 4, 5, 6, 7). This is because some properties show different trends with the spontaneous combustion liability indices (i.e. similar property may be either positive or negative on the two liability indices which is not supposed to be so in a real sense). The lack of significant relationships between all the dependent and independent variables cannot allow separation of the main intrinsic properties influencing spontaneous combustion liability. It is more likely that the intrinsic properties have an influence on one another to some extent during low-temperature oxidation and this dependence of intrinsic properties determine the spontaneous combustion liability. This implies that the most favourable conditions for spontaneous combustion to occur likely depends on the interrelation of intrinsic properties. This necessitated the use of multiple regression to establish interrelationships between the intrinsic properties and spontaneous combustion liability results. The multiple regression analysis was used to derive the predictive models for spontaneous combustion liability of coals and coal-shales. The predictive models were derived by using 12 independent variables. The multiple regression analysis showed that some of the variables were highly correlated with other independent variables. The best model which provides the highest R-squared values and correlation coefficient and lowest standard error of estimate was found through some multiple regression calculations (Table 8).

A statistical standard form from the multiple regression results was selected to analyse and evaluate the influence of selected intrinsic properties on the spontaneous combustion liability of coals and coal-shales. This statistical approach indicated that the changes in spontaneous combustion liability index of coals and coal-shales may be due to an intrinsic parameter, while others are considered. The best prediction for spontaneous combustion liability of 14 coals and 14 coal-shales has been identified in the four models (Table 8). The developed models show that high correlation coefficients and the standard error of estimates values have been reduced to acceptable limits. The multiple regression analysis indicates that the Wits-Ehac Index and intrinsic properties show significant correlation coefficients of 0.939 and 0.998, R-squared values of 0.882 and 0.997, and low standard error of estimates of 0.336 and 0.094 for coals and coal-shales respectively. The Wits-CT Index with intrinsic properties shows significant correlation coefficients of 0.992 and 0.999, R-squared values of 0.983 and 0.999 and higher standard error of estimate of 0.772 and 0.123 for coals and coal-shales respectively. It was found that the models developed for the Wits-Ehac Index gives lower R-squared values, coefficient of correlations and standard error of estimate while, the Wits-CT Index shows higher R-squared values and correlation coefficients and standard error of estimates than the Wits-Ehac Index in both cases. However, considering the index with higher R-squared values and correlation coefficients, it was found that the Wits-CT Index is more suitable to predict the spontaneous combustion liability, while considering the index with low standard error of estimates, the Wits-Ehac Index is also suitable. Hence, multiple regression analysis on the experimental data indicates that the two liability indices can be used to obtain reliable results for spontaneous combustion prediction. Establishing a correlation between liability index and intrinsic properties for coals and coal-shales is essential for a better understanding of the role of coal-shales in spontaneous combustion. The models have shown that spontaneous combustion takes place due to the combined effect of different intrinsic factors.

3.5 Validation of the models

The results of the actual Wits-Ehac and Wits-CT Index for coals and coal-shales are presented in Tables 8 and 9.

The predicted spontaneous combustion liability indices (Wits-Ehac and Wits-CT Index) have been validated with the actual Wits-Ehac Index and the Wits-CT Index and the results are in-line (Tables 9 and 10). Twenty-eight samples evaluated in this paper with an additional four samples (3 coals- KCA, KCB, KCC and KCD; and one coal-shale-KSA) have confirmed the reliability of the developed models. The Wits-Ehac of coal-shales SC, SG, SH, SI, SJ and SM that could not be obtained by the actual Wits-Ehac Index due to their low reactivity were successfully obtained with the predicted models (Table 10). The models present a high level of confidence as they produced results similar to the actual liability indices.

The statistical analysis showed that the spontaneous combustion liability of coals and coal-shales can be determined by a model consisting of various intrinsic factors. The predicted spontaneous combustion liability indices (Wits-Ehac and Wits-CT Index) have been validated with the actual Wits-Ehac Index and the Wits-CT Index and the results are in-line. The developed models enable one to identify the most important factors affecting spontaneous combustion and establishes relationships between them. The intrinsic properties of the samples have been identified to be the main factors contributing towards spontaneous combustion in coal mines. However, the study shows that no single factor is sufficient to influence the coal and coal-shale spontaneous combustion liability but a cumulative effect of favourable parameters may decide whether a coal or coal-shale will be liable to spontaneous combustion or not. The influence of the intrinsic properties of coal-shales in relation to coals could be a tool to predict spontaneous combustion risk in coal mines. The results provide quantitative descriptions and showed the relationships between the dependence of spontaneous combustion liability indices and intrinsic properties. The linear regression analysis shows that both liability indices indicate better linear relationships with some of the intrinsic factors and thus, identifies the major intrinsic factors affecting their liability towards spontaneous combustion. It was found each intrinsic property has an influence on spontaneous combustion liability and their strength varies from one another. Also, a definite positive or negative correlation coefficient exists between the intrinsic factors and the spontaneous combustion test results. The multiple regression of spontaneous combustion liability indices on 12 independent variables has developed acceptable and accurate predictive models as indicated by R-squared values, the coefficient of correlations and standard error of estimates. The models derived from the different samples produced high correlation coefficients and low standard error of estimates. The use of the formulas derived may provide reliable predictions for the spontaneous combustion liability of coals and coal-shales. The influence of the intrinsic properties affecting the spontaneous combustion of coals and coal-shales may be evaluated more effectively by these models than by the linear regression. The results obtained from this study may be used as a reliable tool to support previous works on the role of intrinsic properties on the spontaneous combustion of coals and coal-shales. It has been found that an accurate characterisation of the degree of oxidation could be a useful tool to measure the relative liability of carbonaceous materials toward spontaneous combustion.